View cart “Roland DWX-4 Dental Milling Unit For Sale” has been added to your cart.
-38%
Availability: In Stock
Roland DWX-4W Dental Milling Unit For Sale
$10,500.00$6,500.00
The DWX-4W goes beyond dry milling and is the epitome of wet grinding technology. It uses 4-axis simultaneous movements to wet grind precision inlays, onlays, crowns, veneers and short-span bridges from glass ceramic and composite resins.
Other people want this. 15 people have this in their carts right now.
In addition to milling on X, Y and Z axes, the DWX-4W rotates pin-type blocks 360 degrees on a fourth axis (A axis) to support undercuts. The ball screw-driven 4-axis control allows for smooth, high-precision machining. The DWX-4W’s high-performance 60,000-RPM Jaeger spindle is known for its reliability and supports precision milling of glass ceramics and composite resin. With its multi-pin clamp, the DWX-4W is a wet dental milling machine that can mill up to three different pin-type materials continuously in one operation. As a result, prosthetics for up to three different patients can be produced in a single production run, saving time, labour and costs.
Features and Benefits:
Simultaneous 4-axis machining
4-state Automatic Tool Changer (ATC)
60,000 RPM Jaeger DentaDrive Spindle
CAM software bundled
Virtual Machine Panel (VPanel)
Fully-integrated water and coolant filtration system
Coolant leakage & flow monitoring sensors
Tool life monitoring
Mail notification system
Summary Roland DWX-4W Dental Milling Unit
• Maximum Convenience
• Virtual Machine Panel
• Progress and Error Alerts for Error-Free Milling
• Coolant Compartment and Water Filtration
• Clean Cutting Area for Precision Milling
• Economical Open Architecture
• CAM Software Included
• Growth Potential
• Peace of Mind
The DWX-4W’s high-performance 60 000 RPM Jaeger DentaDrive spindle supports precision milling. It’s equipped to mil pin-type blocks, including glass ceramics and composite resin – acclaimed in the industry for their superior strength and aesthetics. materials can be finished with a short finishing tome, dramatically reducing labour and production time.
In addition to milling on X, Y and Z axes, the DWX-4W rotates pin-type blocks 360 degrees on a fourth axis (A axis) to support undercuts, the rigid ball screw-driven 4-axis control allows for smooth, high-precision machining. With its multi-pin clamp, it can mil up to three different pin-type materials continuously, enabling production three different patient prosthetics in a single production run. it also features an Automatic Tool Changer (ATC) that auto-changes grinding burs without interrupting the production process.
Reviews (0)
Reviews
There are no reviews yet.
Be the first to review “Roland DWX-4W Dental Milling Unit For Sale” Cancel reply
The DWX-4W goes beyond dry milling and is the epitome of wet grinding technology. It uses 4-axis simultaneous movements to wet grind precision inlays, onlays, crowns, veneers and short-span bridges from glass ceramic and composite resins.
iTero HD2.9 simply allows to digitally scan a prepared tooth and wirelessly send this information directly to the dental laboratory for fabrication of a CAD/CAM crown without the gooey mess.
SuniRay 2 achieves maximal image quality with superior diagnostic capabilities while maintaining the lowest radiation levels among all digital sensors. The comprehensive and feature-rich Prof. Suni Advanced Imaging Software supplements the SuniRay 2’s high-quality imaging with a wide array of user-friendly customization and image-enhancement tools. With the SuniRay 2, Suni has created a complete digital radiography system that seamlessly integrates with your entire practice.
The DWX-51D 5-Axis Dental Milling Machine is designed for effortless production of dental prosthetics. Built for precision, error-free milling, you don’t need any machine expertise to operate it. With touch-button controls and automated milling features, the production of high-quality bridges, crowns, inlays, onlays, abutments and other restorations out of 98 mm discs and blocks has been made virtually foolproof.
iRay D3 is one of the most popular products in the world and has been leading the technology since 2004. There are several companies following our concept and make it look similar and sell it cheaper. iRay D3 (DX3000)’s core detail technology and safety features cannot be copied.
The ultimate in ease, material flexibility and unattended production, the DWX-52DC dental milling machine is designed to greatly expand your lab production and profit. Featuring a 6-slot Automatic Disc Changer, 15-station Automatic Tool Changer and other automated features, it gives users of all skill levels an exceptionally powerful, efficient and affordable dental restoration solution.
Reliable High PerformanceIn addition to milling on X, Y and Z axes, the DWX-4W rotates pin-type blocks 360 degrees on a fourth axis (A axis) to support undercuts. The ball screw-driven 4-axis control allows for smooth, high-precision machining. The DWX-4W’s high-performance 60,000-RPM Jaeger spindle is known for its reliability and supports precision milling of glass ceramics and composite resin. With its multi-pin clamp, the DWX-4W is a wet dental milling machine that can mill up to three different pin-type materials continuously in one operation. As a result, prosthetics for up to three different patients can be produced in a single production run, saving time, labour and costs.
Features and Benefits:
Simultaneous 4-axis machining
4-state Automatic Tool Changer (ATC)
60,000 RPM Jaeger DentaDrive Spindle
CAM software bundled
Virtual Machine Panel (VPanel)
Fully-integrated water and coolant filtration system
Coolant leakage & flow monitoring sensors
Tool life monitoring
Mail notification system
Summary Roland DWX-4W Dental Milling Unit
• Maximum Convenience
• Virtual Machine Panel
• Progress and Error Alerts for Error-Free Milling
• Coolant Compartment and Water Filtration
• Clean Cutting Area for Precision Milling
• Economical Open Architecture
• CAM Software Included
• Growth Potential
• Peace of MindThe DWX-4W’s high-performance 60 000 RPM Jaeger DentaDrive spindle supports precision milling. It’s equipped to mil pin-type blocks, including glass ceramics and composite resin – acclaimed in the industry for their superior strength and aesthetics. materials can be finished with a short finishing tome, dramatically reducing labour and production time.In addition to milling on X, Y and Z axes, the DWX-4W rotates pin-type blocks 360 degrees on a fourth axis (A axis) to support undercuts, the rigid ball screw-driven 4-axis control allows for smooth, high-precision machining. With its multi-pin clamp, it can mil up to three different pin-type materials continuously, enabling production three different patient prosthetics in a single production run. it also features an Automatic Tool Changer (ATC) that auto-changes grinding burs without interrupting the production process.
iTero HD2.9 simply allows to digitally scan a prepared tooth and wirelessly send this information directly to the dental laboratory for fabrication of a CAD/CAM crown – without the gooey mess. The wireless transmission saves shipping time and eliminates distortion that can often be found with traditional stone modelsThe digital scan is, quite literally, digitally perfect. We then deliver the digital scan to our lab where a precision fitting restoration is created.iTero HD2.9 system eliminated the uncomfortable patient experience of traditional impressions, utilizes advanced state of the art digital technology, and provides with superior fitting restorations with little or no adjustmentsiTero Intra-Oral Scanner
Model: HD2.9
2014 Date of Mfg.
Brochure/Video: Click Here
Limited Use
Includes:
iTero Software (pre-loaded)
90 Day Parts Warranty
User Manual(s)
Free Standard Shipping (Commercial USA Addresses)
Its ergonomic design comes with safe docking station. It has thin fiber optic cable which enables quick data transfer from the wand to the cart. This optimized cable length assists various cart positions in the operatory.Orthodontic treatment is more than just straightening teeth; it’s about ensuring your teeth and jaws are in alignment. To achieve this, we need to get an accurate look at where your teeth are positioned. To do this, we use the iTero Intraoral digital scanner.A good impressionIn the orthodontic and dental industries, ‘impressions’ is the term we use for getting a good picture of where your teeth currently sit. These impressions were previously taken using a type of dental cement. Pasted on your teeth, patients were required to lie for a few minutes while the cement-like material set. The dental professional could then remove the set material which had formed an ‘impression’ of your teeth.This process was messy, rather unpleasant and not very comfortable. Fortunately, that method is a thing of the past. These days, we use scanning technology and at L&L Orthodontics, our technology of choice is the iTero Intraoral digital scanner.
What is the iTero scanner?
The iTero scanner is new 3D orthodontic scanning technology. Using the latest developments in intraoral scanning, the iTero scanner accurately scans your teeth as part of your orthodontic assessment. The iTero scanner is made up of a small, wand-like device which is used to scan your teeth and jaws. The data it is collecting then appears on the computer screen, allowing you to see the ‘impressions’ the scanner is taking.The iTero scanner works in with Invisalign®* treatment and lets you see what your teeth will look like post-treatment, even before you’ve started. Before we recommend a course of treatment for you, we’ll take impressions of your teeth using the iTero scanner to ensure we are making our recommendation on accurate information.To find out more about the iTero scanner and other orthodontic technology we use here at L&L Orthodontics, book your specialist consultation today.
SuniRay 2 Digital Intraoral Sensor Size 1 and Size 2
X-Ray Imaging Properties
Resolution: The pixel resolution of the high resolution (HiRes) sensors exceeds 15 lp/mm. The standard resolution of an X-Ray image, as measured by the modulation transfer function (MTF) exceeds 12 lp/mm. This is measured by using a standard 60 kV intraoral X-ray source.
Does Efficiency: The sensor will produce a high quality image with an X-Ray dose that is only a fraction of the standard dose required by Dental X-Ray film.
Diagnostic Efficacy: The system will produce a superior image quality of images obtained when using standard dental X-Ray film. This allows the dentist to diagnose standard intraoral pathologies encountered during screening procedures.
Wide dynamic range: The sensor pixel well capacity is very high, allowing a higher accommodation of greyscale (bone density) dynamic range.
Sensor Material Biocompatibility SpecificationsThe sensor’s body material and cable material are biocompatible. The sensors and all component materials have been tested to comply with ISO standards, and specifically, the sensor complies with EN IS0-10993 (Biological Evaluation of Medical Devices).
Technical data
Size 1
Size 2
Sensor Dimensions (mm)
39.5 x 26
43.5 x 31.5
Active Area (mm)
31.1 x 20.2
35.2 x 26.2
Sensor Technology
CMOS APS Fiber Plate
CMOS APS Fiber Plate
Maximum Gray Levels
4096
4096
Sensor Cable
3 feet (1m)
3 feet (1m)
Cable Attachment
Reinforced Strain Relief
Reinforced Strain Relief
USB Module
Integrated USB 2.0 Module
Integrated USB 2.0 Module
Software
Prof. Suni
Prof. Suni
X-Ray Imaging Properties SuniRay 2 Digital Intraoral Sensor Size 1 and Size 2
Resolution: The pixel resolution of the high resolution (HiRes) sensors exceeds 15 lp/mm. The standard resolution of an X-Ray image, as measured by the modulation transfer function (MTF) exceeds 12 lp/mm. This is measured by using a standard 60 kV intraoral X-ray source.
Does Efficiency: The sensor will produce a high quality image with an X-Ray dose that is only a fraction of the standard dose required by Dental X-Ray film.
Diagnostic Efficacy: The system will produce a superior image quality of images obtained when using standard dental X-Ray film. This allows the dentist to diagnose standard intraoral pathologies encountered during screening procedures.
Wide dynamic range: The sensor pixel well capacity is very high, allowing a higher accommodation of greyscale (bone density) dynamic range.
Roland DWX-51D Dental Milling Unit
The DWX-51D 5-Axis Dental Milling Machine is designed for effortless production of dental prosthetics. Built for precision, error-free milling, you don’t need any machine expertise to operate it. With touch-button controls and automated milling features, the production of high-quality bridges, crowns, inlays, onlays, abutments and other restorations out of 98 mm discs and blocks has been made virtually foolproof.
5-axis simultaneous milling for complex prosthetics and full mouth restorations
Precision milling of wax, zirconia, PEEK, gypsum and PMMA
10-station Automatic Tool Changer (ATC) with tool length sensor
Built-in dust collection system for maximum extraction and easy cleaning
5-Axis Machining for Smoother Production
The DWX-51D is a smooth and steady ball screw-driven machine capable of milling complex restorations. It operates on X,Y, and Z axes – simultaneously rotating blocks and discs. Tilting on the B axis it supports deep undercuts and the complex milling of large arch restorations and other full-mouth prosthetics.Clean and Comfortable Operation
A unique inner structure with spacious airflow supports comfortable operation, while an automatic dust collection feature boasts a powerful vacuum for clean usage and calibration. An ionizer removes static, ideal for milling PMMA material.Economical Open Architecture
The open architecture of the DWX-51D allows you to work with the latest materials, CAD/CAM software and scanners, without needing to rely on a single source.VPanel for Simplified Operation
Complex controls associated with CNC milling have been replaced by a user-friendly Virtual Machine Panel (VPanel) that automatically starts the milling process, conducts machine diagnostics and operates milling calibration from your computer.New C-Clamp for Quicker Set-Up
The new C-clamp on the DWX-51D requires the adjustment of only two screws for a simplified set-up. The C-clamp (which includes a torque driver for improved clamping consistency) also provides exact alignment and uniformity, resulting in less misalignment issues.10-Station Automatic Tool Changer for Continuous Milling With a 10-station Automatic Tool Changer (ATC), DWX-51D users don’t have to stop production to replace the specific burs needed for milling different materials.User Replaceable Spindle Roland DWX-51D Dental Milling Unit
When the spindle needs replacing on the DWX-51D, there’s no need to stop production and pay for a technician to come out. Featuring a spindle that users can replace themselves, production never has to come to a complete standstill.Progress and Error Alerts for Error-Free Milling
To further automate the milling process and ensure error-free production, users receive e-mail notifications detailing any errors, or when milling is completed, while a color-coded LED light signals machine status.9 Pin-Type Material Adapter Included
A material adapter with nine pin-type placement options is included for easy and error free set-up.VITA Certified
VITA certifies the Roland DWX-51D for milling VITA ENAMIC. The DWX-51D is the only dry-milling system that, when equipped with our ZBD-100D-HY /50D-HY /30D-HY hybrid tools, is authorized to mill VITA ENAMIC and produce a full-range of dental prosthetics. Other material brands are also available for milling with the DWX-51D.Peace of Mind, Reliability and Support
The DWX-51D offers unmatched reliability and post-sales support that includes a two-year warranty. Enjoy the benefit of certified service engineers to ensure that your device is always up-and-running and a dedicated online and telephone support staff who can answer all your questions and concerns.
Dexcowin IRay D3 Dental Handheld X-Ray System
iRay D3 Dental Mobile Handheld X-Ray
Dexcowin invented the iRay D3 more than 10 years ago, in 2004, after several years of R&D. The iRay D3 has some different names for the OEM, but the official product model name is DX3000. We have designed it as a pure handheld portable X-ray. It has many different features for mobile, battery powered, handheld, cordless, digital, and camera types. It is lightweight, durable, stable, easy to use, saleable, and compatible to all radiation detectors, with clear, effective images. However, what we would like to emphasize, and what we are so proud of about the iRay D3 is that it is safe for handheld use. This is because we are concerned about the safety and care of the operators and patients. This is our top priority and responsibility to our customers. We follow all required rules from FDA, GMP, CE and all local health departments from the over 40 countries and states we have registered in. We keep to the safety regulations during manufacturing. Our long term company strategy for iRay D3 is to “Make it safe,” “”Make it better than yesterday,” and “Make it durable.”A summary of iRay D3 features Dexcowin IRay D3 Dental Handheld X-Ray SystemiRay D3 Convenience & Cost effectiveness
You can stay with the patient, and it is especially beneficial for children.
No need to construct separate shielded rooms, so all operation rooms can be X-ray rooms.
Lightweight 4 lbs gives you handy operation and saves time for full mouth X-ray.
More than 200 shots on single charge (1.5 hour). Battery and a spare battery included.iRay D3 compatibility
Applicable and be compatible with all detectors, film, PSP and all kinds of sensors.IRay D3 Mobility
Completely mobile system with a battery and extras.
Compact design and lightweight allows it to be moved anywhere in and out of office.IRay D3 Safety
Designed for handheld, so it does not affect the operator with extremely low leakage radiation.
Rechargeable Lithium polymer battery is very safe and stable with a safety circuit
Battery can be charged separately with a main X-ray body.Other accessories
AllMyT mobile cart for iRay D3 to be mounted on.
A neck strap to balance the weight and preventing dropping.
The DWX-52DC Dental Mill with Disc Changer is the newest addition to the popular DWX series of 5-Axis Dental Milling Machines. With a combination of automated functions designed to help reduce manual work, production of dental restorations is now even more efficient and reliable. The DWX-52DC’s open architecture means it can be used with the CAD/CAM software that your technicians are already familiar with in order to cut learning time and create the optimum workflow for your production environment. The DWX-52DC provides an efficient digital solution for both dental laboratories seeking to boost production capabilities, as well as labs looking to expand into the digital realm.
95 mm (diameter), height max. 35 mm
Pin diameter: 6 mm
Pin diameter:
6 mm
Loadable workpiece weight
Up to 850 g
Number of adapters housed
6
Operating speed
XYZ axis:
0.24 to 70.9 in./min.(6 to 1,800 mm/min.)
Spindle motor
Brushless DC Motor
Spindle speed
6,000 to 30,000 rpm
Rotary axis travel angle
A:
±360°
B:
±30°
Number of burs housed
15
Attachable bur
Shank diameter:
4 mm
Length:
40 to 55 mm
Compatible compressed air
0.2 MPa
Interface
USB
Control command set
RML-1, NC code
Power requirements
AC 100 V to 240 V ±10%, 50/60 Hz, 2.0 A
(overvoltage category II, IEC60664-1)
Power consumption
Approx. 200 W
Operating noise
During operation:
70 dB (A) or less (when not cutting),
During standby:
45 dB (A) or less
External dimensions
Width x Depth x Height:
34.6 x 26.0 x 23.6 in. (880 x 660 x 600 mm)
Weight:
105 kg (231.5 lbs.)
The ultimate in ease, material flexibility and unattended production, the DWX-52DC dental milling machine is designed to greatly expand your lab production and profit. Featuring a 6-slot Automatic Disc Changer, 15-station Automatic Tool Changer and other automated features, it gives users of all skill levels an exceptionally powerful, efficient and affordable dental restoration solution.
Reviews
There are no reviews yet.