View cart “GE Logiq Book XP Ultrasound” has been added to your cart.
-38%
Availability: In Stock
QuickRay USB Size 1 And 2 X-Ray Sensor For Sale
$4,000.00$2,500.00
Are you paying too much for digital X-ray sensors and warranties? Consider QuickRay from Video Dental Concepts! A dental imaging leader and innovator since 1989, VDC has provided over 7,000 dental professionals with the best diagnostic imaging values and personalized support for over 20 years.
Other people want this. 15 people have this in their carts right now.
QuickRay USB is a breakthrough in digital X-rays. The embedded electronics are located in the sensor case so there is no interface box! Simply connect the sensor cable via its USB connector to your computer and go! QuickRay USB is currently compatible with these Apteryx based software systems: XVa3, XVLite, Cliniview, Clinitouch, XDR Imaging, MPDX-DMD, Lightyear, DentiMax, ProfSuni, Dr. Suni, Sigma, AFP Digital and Belmont.
Great value QuickRay USB digital X-ray sensors connect directly to USB— no interface box needed!
Are you paying too much for digital X-ray sensors and warranties? Consider QuickRay from Video Dental Concepts! A dental imaging leader and innovator since 1989, VDC has provided over 7,000 dental professionals with the best diagnostic imaging values and personalized support for over 20 years.
QuickRay USB Size 1 And 2 X-Ray Sensor For Sale
QuickRay USB is a breakthrough in digital X-rays. The embedded electronics are located in the sensor case so there is no interface box! Simply connect the sensor cable via its USB connector to your computer and go! QuickRay USB is currently compatible with these Apteryx based software systems: XVa3, XVLite, Cliniview, Clinitouch, XDR Imaging, MPDX-DMD, Lightyear, DentiMax, ProfSuni, Dr. Suni, Sigma, AFP Digital and Belmont.
The QuickRay sensor gives you the highest resolution and clarity! The thin (less than 1/4″) intraoral sensors include a CMOS image sensor chip, CsI Scintillator, electronic circuits, shielding foils and shock absorbers. Tough polyamide housings have durable replaceable polyurethane cables with ergonomically placed connectors. Their rounded corners and smooth edges optimize patient comfort.
And QuickRay is the fastest sensor on the market! View X-rays in USB 2.0 High Speed Mode in only 3 seconds. Operate in USB 2.0 Full Speed Mode, if necessary.
Every sensor is covered by the VDC two year warranty with no annual fees. Technical support is available for an additional fee on an annual basis. Optional pro rata warranty is available from VDC after purchase. All VDC products are FDA registered.
Reviews (0)
Reviews
There are no reviews yet.
Be the first to review “QuickRay USB Size 1 And 2 X-Ray Sensor For Sale” Cancel reply
Are you paying too much for digital X-ray sensors and warranties? Consider QuickRay from Video Dental Concepts! A dental imaging leader and innovator since 1989, VDC has provided over 7,000 dental professionals with the best diagnostic imaging values and personalized support for over 20 years.
3 Shape D2000 Dental lab Scanner Optimized processing speed: creates faster performance and better scanning workflows for several indications Shortens waiting time between creating orders and starting the scan, and enables technicians to begin next scan without having to wait for post processing.
SuniRay 2 achieves maximal image quality with superior diagnostic capabilities while maintaining the lowest radiation levels among all digital sensors. The comprehensive and feature-rich Prof. Suni Advanced Imaging Software supplements the SuniRay 2’s high-quality imaging with a wide array of user-friendly customization and image-enhancement tools. With the SuniRay 2, Suni has created a complete digital radiography system that seamlessly integrates with your entire practice.
iTero HD2.9 simply allows to digitally scan a prepared tooth and wirelessly send this information directly to the dental laboratory for fabrication of a CAD/CAM crown without the gooey mess.
The DWX-4W goes beyond dry milling and is the epitome of wet grinding technology. It uses 4-axis simultaneous movements to wet grind precision inlays, onlays, crowns, veneers and short-span bridges from glass ceramic and composite resins.
The ultimate in ease, material flexibility and unattended production, the DWX-52DC dental milling machine is designed to greatly expand your lab production and profit. Featuring a 6-slot Automatic Disc Changer, 15-station Automatic Tool Changer and other automated features, it gives users of all skill levels an exceptionally powerful, efficient and affordable dental restoration solution.
Content
QuickRay USB Size 1 And 2 X-Ray Sensor
QuickRay USB is a breakthrough in digital X-rays. The embedded electronics are located in the sensor case so there is no interface box! Simply connect the sensor cable via its USB connector to your computer and go! QuickRay USB is currently compatible with these Apteryx based software systems: XVa3, XVLite, Cliniview, Clinitouch, XDR Imaging, MPDX-DMD, Lightyear, DentiMax, ProfSuni, Dr. Suni, Sigma, AFP Digital and Belmont.Great value QuickRay USB digital X-ray sensors connect directly to USB— no interface box needed!Are you paying too much for digital X-ray sensors and warranties? Consider QuickRay from Video Dental Concepts! A dental imaging leader and innovator since 1989, VDC has provided over 7,000 dental professionals with the best diagnostic imaging values and personalized support for over 20 years.QuickRay USB Size 1 And 2 X-Ray Sensor For SaleQuickRay USB is a breakthrough in digital X-rays. The embedded electronics are located in the sensor case so there is no interface box! Simply connect the sensor cable via its USB connector to your computer and go! QuickRay USB is currently compatible with these Apteryx based software systems: XVa3, XVLite, Cliniview, Clinitouch, XDR Imaging, MPDX-DMD, Lightyear, DentiMax, ProfSuni, Dr. Suni, Sigma, AFP Digital and Belmont.The QuickRay sensor gives you the highest resolution and clarity! The thin (less than 1/4″) intraoral sensors include a CMOS image sensor chip, CsI Scintillator, electronic circuits, shielding foils and shock absorbers. Tough polyamide housings have durable replaceable polyurethane cables with ergonomically placed connectors. Their rounded corners and smooth edges optimize patient comfort.
And QuickRay is the fastest sensor on the market! View X-rays in USB 2.0 High Speed Mode in only 3 seconds. Operate in USB 2.0 Full Speed Mode, if necessary.Every sensor is covered by the VDC two year warranty with no annual fees. Technical support is available for an additional fee on an annual basis. Optional pro rata warranty is available from VDC after purchase. All VDC products are FDA registered.
– Impression scanning:
Multi line scanning in the D2000 and D1000 improves coverage and performance for accurate scanning of impressions to enable restorative design without the need to pour gypsum models.
All in One scanning of triple tray impressions Special mount enables triple-tray scanning capture of upper, lower and bite in one scan.– Improved workflows for single tray impressions:
Provides support for single tray impression scanning including bite alignment.The software upgrades are available for all relevant 3Shape lab scanner models. Current lab scanner owners will receive the upgrades as a LABcare software update, where applicable.Impression scanning the future is now:
The D2000 and the smaller D1000 lab scanner feature multi-line technology. Multi-line technology utilizes multiple scan lines in a single shot to significantly improve cavity and impression capture.This enables the D2000 to accurately scan analog impressions sent to the lab by a dentist. This in turn, eliminates the need for labs having to pour or create a gypsum model from the impression. This saves several steps in the workflow and allows labs to print instead, cost effective 3D models derived from the analog impression if they need a physical working model.While all 3shape scanners support impression scanning only the D2000 and D1000 feature multi line technology.“Impression scanning is today’s reality and the future. No waiting for models to set, no plaster inaccuracies and we reduce costs. Every lab should invest in this technology,” Carlo Backes, Excent Tandtechniek BV, Holland.About the D2000 dental lab scanner:
Introduced at the 2015 Midwinter show, the D2000 was named a top 10 coolest product at the event. The D2000 captivated the industry by having room for two models in its interior, enabling technicians to scan two models at once and perform a complete case like a three-unit bridge in just one scan.D2000 All in-one scanning for max volume throughputs
– 4 x 5 MP cameras, Blue LED Multi-line
– Accuracy: 5 µm (ISO 12836) / 8 µm (Implant bar)
– Die scan time: 15 sec
– Full arch scan time: 20 sec
– Color texture scanning
– No need for separate die scan
– All in One scanning: room for 2 models
– Impression scanningIncludes:3SHAPE D2000 DENTAL LAB 3D SCANNER
– Remainder of a 5 year factory warranty
– 3 Shape Dental Designer w/Additional Seat
– 3 Shape Model Builder
– 3 Shape Occlusion Set Up Tool
– ScanIt Impression Module
– Impression Fixture
– Anatomical CAD Library
– Calibration Kit
– HP Envy Phoenix Desktop PC
SuniRay 2 Digital Intraoral Sensor Size 1 and Size 2
X-Ray Imaging Properties
Resolution: The pixel resolution of the high resolution (HiRes) sensors exceeds 15 lp/mm. The standard resolution of an X-Ray image, as measured by the modulation transfer function (MTF) exceeds 12 lp/mm. This is measured by using a standard 60 kV intraoral X-ray source.
Does Efficiency: The sensor will produce a high quality image with an X-Ray dose that is only a fraction of the standard dose required by Dental X-Ray film.
Diagnostic Efficacy: The system will produce a superior image quality of images obtained when using standard dental X-Ray film. This allows the dentist to diagnose standard intraoral pathologies encountered during screening procedures.
Wide dynamic range: The sensor pixel well capacity is very high, allowing a higher accommodation of greyscale (bone density) dynamic range.
Sensor Material Biocompatibility SpecificationsThe sensor’s body material and cable material are biocompatible. The sensors and all component materials have been tested to comply with ISO standards, and specifically, the sensor complies with EN IS0-10993 (Biological Evaluation of Medical Devices).
Technical data
Size 1
Size 2
Sensor Dimensions (mm)
39.5 x 26
43.5 x 31.5
Active Area (mm)
31.1 x 20.2
35.2 x 26.2
Sensor Technology
CMOS APS Fiber Plate
CMOS APS Fiber Plate
Maximum Gray Levels
4096
4096
Sensor Cable
3 feet (1m)
3 feet (1m)
Cable Attachment
Reinforced Strain Relief
Reinforced Strain Relief
USB Module
Integrated USB 2.0 Module
Integrated USB 2.0 Module
Software
Prof. Suni
Prof. Suni
X-Ray Imaging Properties SuniRay 2 Digital Intraoral Sensor Size 1 and Size 2
Resolution: The pixel resolution of the high resolution (HiRes) sensors exceeds 15 lp/mm. The standard resolution of an X-Ray image, as measured by the modulation transfer function (MTF) exceeds 12 lp/mm. This is measured by using a standard 60 kV intraoral X-ray source.
Does Efficiency: The sensor will produce a high quality image with an X-Ray dose that is only a fraction of the standard dose required by Dental X-Ray film.
Diagnostic Efficacy: The system will produce a superior image quality of images obtained when using standard dental X-Ray film. This allows the dentist to diagnose standard intraoral pathologies encountered during screening procedures.
Wide dynamic range: The sensor pixel well capacity is very high, allowing a higher accommodation of greyscale (bone density) dynamic range.
iTero HD2.9 simply allows to digitally scan a prepared tooth and wirelessly send this information directly to the dental laboratory for fabrication of a CAD/CAM crown – without the gooey mess. The wireless transmission saves shipping time and eliminates distortion that can often be found with traditional stone modelsThe digital scan is, quite literally, digitally perfect. We then deliver the digital scan to our lab where a precision fitting restoration is created.iTero HD2.9 system eliminated the uncomfortable patient experience of traditional impressions, utilizes advanced state of the art digital technology, and provides with superior fitting restorations with little or no adjustmentsiTero Intra-Oral Scanner
Model: HD2.9
2014 Date of Mfg.
Brochure/Video: Click Here
Limited Use
Includes:
iTero Software (pre-loaded)
90 Day Parts Warranty
User Manual(s)
Free Standard Shipping (Commercial USA Addresses)
Its ergonomic design comes with safe docking station. It has thin fiber optic cable which enables quick data transfer from the wand to the cart. This optimized cable length assists various cart positions in the operatory.Orthodontic treatment is more than just straightening teeth; it’s about ensuring your teeth and jaws are in alignment. To achieve this, we need to get an accurate look at where your teeth are positioned. To do this, we use the iTero Intraoral digital scanner.A good impressionIn the orthodontic and dental industries, ‘impressions’ is the term we use for getting a good picture of where your teeth currently sit. These impressions were previously taken using a type of dental cement. Pasted on your teeth, patients were required to lie for a few minutes while the cement-like material set. The dental professional could then remove the set material which had formed an ‘impression’ of your teeth.This process was messy, rather unpleasant and not very comfortable. Fortunately, that method is a thing of the past. These days, we use scanning technology and at L&L Orthodontics, our technology of choice is the iTero Intraoral digital scanner.
What is the iTero scanner?
The iTero scanner is new 3D orthodontic scanning technology. Using the latest developments in intraoral scanning, the iTero scanner accurately scans your teeth as part of your orthodontic assessment. The iTero scanner is made up of a small, wand-like device which is used to scan your teeth and jaws. The data it is collecting then appears on the computer screen, allowing you to see the ‘impressions’ the scanner is taking.The iTero scanner works in with Invisalign®* treatment and lets you see what your teeth will look like post-treatment, even before you’ve started. Before we recommend a course of treatment for you, we’ll take impressions of your teeth using the iTero scanner to ensure we are making our recommendation on accurate information.To find out more about the iTero scanner and other orthodontic technology we use here at L&L Orthodontics, book your specialist consultation today.
Reliable High PerformanceIn addition to milling on X, Y and Z axes, the DWX-4W rotates pin-type blocks 360 degrees on a fourth axis (A axis) to support undercuts. The ball screw-driven 4-axis control allows for smooth, high-precision machining. The DWX-4W’s high-performance 60,000-RPM Jaeger spindle is known for its reliability and supports precision milling of glass ceramics and composite resin. With its multi-pin clamp, the DWX-4W is a wet dental milling machine that can mill up to three different pin-type materials continuously in one operation. As a result, prosthetics for up to three different patients can be produced in a single production run, saving time, labour and costs.
Features and Benefits:
Simultaneous 4-axis machining
4-state Automatic Tool Changer (ATC)
60,000 RPM Jaeger DentaDrive Spindle
CAM software bundled
Virtual Machine Panel (VPanel)
Fully-integrated water and coolant filtration system
Coolant leakage & flow monitoring sensors
Tool life monitoring
Mail notification system
Summary Roland DWX-4W Dental Milling Unit
• Maximum Convenience
• Virtual Machine Panel
• Progress and Error Alerts for Error-Free Milling
• Coolant Compartment and Water Filtration
• Clean Cutting Area for Precision Milling
• Economical Open Architecture
• CAM Software Included
• Growth Potential
• Peace of MindThe DWX-4W’s high-performance 60 000 RPM Jaeger DentaDrive spindle supports precision milling. It’s equipped to mil pin-type blocks, including glass ceramics and composite resin – acclaimed in the industry for their superior strength and aesthetics. materials can be finished with a short finishing tome, dramatically reducing labour and production time.In addition to milling on X, Y and Z axes, the DWX-4W rotates pin-type blocks 360 degrees on a fourth axis (A axis) to support undercuts, the rigid ball screw-driven 4-axis control allows for smooth, high-precision machining. With its multi-pin clamp, it can mil up to three different pin-type materials continuously, enabling production three different patient prosthetics in a single production run. it also features an Automatic Tool Changer (ATC) that auto-changes grinding burs without interrupting the production process.
The DWX-52DC Dental Mill with Disc Changer is the newest addition to the popular DWX series of 5-Axis Dental Milling Machines. With a combination of automated functions designed to help reduce manual work, production of dental restorations is now even more efficient and reliable. The DWX-52DC’s open architecture means it can be used with the CAD/CAM software that your technicians are already familiar with in order to cut learning time and create the optimum workflow for your production environment. The DWX-52DC provides an efficient digital solution for both dental laboratories seeking to boost production capabilities, as well as labs looking to expand into the digital realm.
95 mm (diameter), height max. 35 mm
Pin diameter: 6 mm
Pin diameter:
6 mm
Loadable workpiece weight
Up to 850 g
Number of adapters housed
6
Operating speed
XYZ axis:
0.24 to 70.9 in./min.(6 to 1,800 mm/min.)
Spindle motor
Brushless DC Motor
Spindle speed
6,000 to 30,000 rpm
Rotary axis travel angle
A:
±360°
B:
±30°
Number of burs housed
15
Attachable bur
Shank diameter:
4 mm
Length:
40 to 55 mm
Compatible compressed air
0.2 MPa
Interface
USB
Control command set
RML-1, NC code
Power requirements
AC 100 V to 240 V ±10%, 50/60 Hz, 2.0 A
(overvoltage category II, IEC60664-1)
Power consumption
Approx. 200 W
Operating noise
During operation:
70 dB (A) or less (when not cutting),
During standby:
45 dB (A) or less
External dimensions
Width x Depth x Height:
34.6 x 26.0 x 23.6 in. (880 x 660 x 600 mm)
Weight:
105 kg (231.5 lbs.)
The ultimate in ease, material flexibility and unattended production, the DWX-52DC dental milling machine is designed to greatly expand your lab production and profit. Featuring a 6-slot Automatic Disc Changer, 15-station Automatic Tool Changer and other automated features, it gives users of all skill levels an exceptionally powerful, efficient and affordable dental restoration solution.
Reviews
There are no reviews yet.