Ivoclar Vivadent Programat CS4 is a compact multifunction furnace for dental practices. It is designed for sintering zirconia restorations, e.g. IPS e.max ZirCAD, using a temperature of up to 1,600°C. The furnace can also be employed as a glazing and crystallisation furnace for IPS e.max CAD and IPS Empress CAD restorations. The speed sintering program allows zirconia restorations to be manufactured directly in the dental practice in a single session.
A clearly arranged membrane-sealed keypad with graphic display enables easy operation. Both pre-set and individual programs for third-party materials are available. Programat CS4 is a stand-alone furnace that features an open system.
Ivoclar Vivadent Programat CS4 Advantages:
Fast sintering of IPS e.max ZirCAD
Crystallisation of IPS e.max CAD
Glaze program for IPS e.max ZirCAD, IPS e.max CAD and IPS Empress CAD
High processing capacity (up to six units)
Open system
Simple and language-independent operation due to the proven combination of membrane-sealed keypad and graphic display
Power Saving Technology
Compact design
Possibility of on-site temperature calibration
OSD (Optical Status Display)
Remote control via PC/laptop by means of PrograBase3 software
Ivoclar Vivadent Programat CS4 Key features
The firing chamber can be heated up to 1600 ° C;
The electronics with the corresponding software controls the sintering program;
There is a constant comparison between the actual and the set temperature;
The sintering table can accommodate up to 6 single restorations at the same time
Ivoclar Vivadent Programat CS4 Features of the model
Fast sintering process (it is possible to manufacture ZrO2 restorations in one medical appointment, maximum – six units at a time);
Glaze firing and crystallization (cost-saving, as usually different furnaces, are required for sintering, glaze firing, and crystallization);
Precise temperature (precise temperature control for glaze firing, crystallization, and sintering).
Ivoclar Vivadent Programat CS4 Application
Sintering and glazing of ZrO 2 materials (eg IPS e.max ZirCAD);
Crystallization and glazing (e.g. IPS e.max CAD).
The Programat CS4 cannot be used as a ceramic kiln for ceramics in the dental laboratory.
Specifications Ivoclar Vivadent Programat CS4
Power supply: 118-240 V / 50-60 Hz
Overvoltage category: II
Pollution degree: 2
Allowable voltage fluctuations: + – 10%
Maximum current consumption: 16A @ 118V, 8A @ 240V
Electrical fuses: 250 V / T 16 A (heating element)
Fuse size: diameter 5 x 20 mm
Closed oven dimensions: depth – 430 mm, width – 310 mm (with stand – 390 mm), height – 570 mm
Useful chamber volume: diameter – 80 mm, height – 80 mm
Maximum firing temperature: 1600 ° C
Weight: bottom 10 kg, furnace head 17 kg
Equipment
The lower part of the oven is electronically controlled;
Furnace head with sintering chamber;
Sintering table;
Object stand;
Network cable;
Table fork;
Cleaning brush;
Crystallization table.
Delivery forms
Programat CS4
Power cord
Sintering Furnace Temperature Checking Set Starter Kit – Operating Instructions
Sinter tray
Sinter tray fork
IPS e.max Speed Crystallization Tray
USB download cable
var. accessories
Instructions for Use
Warranty Card
Reviews (0)
Reviews
There are no reviews yet.
Be the first to review “Ivoclar Vivadent Programat CS4” Cancel reply
Programat CS4 is the ideal sintering, crystallisation and glazing furnace for dental practices.
iTero HD2.9 simply allows to digitally scan a prepared tooth and wirelessly send this information directly to the dental laboratory for fabrication of a CAD/CAM crown without the gooey mess.
The Identica T300 dramatically improves the fundamental aspects of scanner performance and the latest software technology provides the clearest, sharpest data. Identica T300 is customized to deliver the finest data quality using its dual 2.0 MP cameras. Identica T300 will save valuable time and money by minimizing trial & error when adjusting restoration fits.
Because the XIOS Scan imaging plates were developed specifically for the Sirona scanner, they offer particularly high image quality. For better identification and visibility in the mouth, the plates have a white, inactive back and a blue, active side.
The ultimate in ease, material flexibility and unattended production, the DWX-52DC dental milling machine is designed to greatly expand your lab production and profit. Featuring a 6-slot Automatic Disc Changer, 15-station Automatic Tool Changer and other automated features, it gives users of all skill levels an exceptionally powerful, efficient and affordable dental restoration solution.
Intelligent Machine. Effortless Production. Superior Results.
The DGSHAPE DWX-42W enables wet milling of popular glass ceramic and composite resins with high precision and accuracy.
High speed production with proprietary DGSHAPE spindle
Expanded 6-tool Automatic Tool Changer for uninterrupted milling
LAN capable for easy connectivity
Included VPanel for easy monitoring of milling jobs and tools
Content
Ivoclar Vivadent Programat CS4
Ivoclar Vivadent Programat CS4 is a compact multifunction furnace for dental practices. It is designed for sintering zirconia restorations, e.g. IPS e.max ZirCAD, using a temperature of up to 1,600°C. The furnace can also be employed as a glazing and crystallisation furnace for IPS e.max CAD and IPS Empress CAD restorations. The speed sintering program allows zirconia restorations to be manufactured directly in the dental practice in a single session.
A clearly arranged membrane-sealed keypad with graphic display enables easy operation. Both pre-set and individual programs for third-party materials are available. Programat CS4 is a stand-alone furnace that features an open system.Ivoclar Vivadent Programat CS4 Advantages:
Fast sintering of IPS e.max ZirCAD
Crystallisation of IPS e.max CAD
Glaze program for IPS e.max ZirCAD, IPS e.max CAD and IPS Empress CAD
High processing capacity (up to six units)
Open system
Simple and language-independent operation due to the proven combination of membrane-sealed keypad and graphic display
Power Saving Technology
Compact design
Possibility of on-site temperature calibration
OSD (Optical Status Display)
Remote control via PC/laptop by means of PrograBase3 software
Ivoclar Vivadent Programat CS4 Key features
The firing chamber can be heated up to 1600 ° C;
The electronics with the corresponding software controls the sintering program;
There is a constant comparison between the actual and the set temperature;
The sintering table can accommodate up to 6 single restorations at the same time
Ivoclar Vivadent Programat CS4 Features of the model
Fast sintering process (it is possible to manufacture ZrO2 restorations in one medical appointment, maximum – six units at a time);
Glaze firing and crystallization (cost-saving, as usually different furnaces, are required for sintering, glaze firing, and crystallization);
Precise temperature (precise temperature control for glaze firing, crystallization, and sintering).
Ivoclar Vivadent Programat CS4 Application
Sintering and glazing of ZrO 2 materials (eg IPS e.max ZirCAD);
Crystallization and glazing (e.g. IPS e.max CAD).
The Programat CS4 cannot be used as a ceramic kiln for ceramics in the dental laboratory.
Specifications Ivoclar Vivadent Programat CS4
Power supply: 118-240 V / 50-60 Hz
Overvoltage category: II
Pollution degree: 2
Allowable voltage fluctuations: + – 10%
Maximum current consumption: 16A @ 118V, 8A @ 240V
Electrical fuses: 250 V / T 16 A (heating element)
Fuse size: diameter 5 x 20 mm
Closed oven dimensions: depth – 430 mm, width – 310 mm (with stand – 390 mm), height – 570 mm
Useful chamber volume: diameter – 80 mm, height – 80 mm
Maximum firing temperature: 1600 ° C
Weight: bottom 10 kg, furnace head 17 kg
Equipment
The lower part of the oven is electronically controlled;
Furnace head with sintering chamber;
Sintering table;
Object stand;
Network cable;
Table fork;
Cleaning brush;
Crystallization table.
Delivery forms
Programat CS4
Power cord
Sintering Furnace Temperature Checking Set Starter Kit – Operating Instructions
iTero HD2.9 simply allows to digitally scan a prepared tooth and wirelessly send this information directly to the dental laboratory for fabrication of a CAD/CAM crown – without the gooey mess. The wireless transmission saves shipping time and eliminates distortion that can often be found with traditional stone modelsThe digital scan is, quite literally, digitally perfect. We then deliver the digital scan to our lab where a precision fitting restoration is created.iTero HD2.9 system eliminated the uncomfortable patient experience of traditional impressions, utilizes advanced state of the art digital technology, and provides with superior fitting restorations with little or no adjustmentsiTero Intra-Oral Scanner
Model: HD2.9
2014 Date of Mfg.
Brochure/Video: Click Here
Limited Use
Includes:
iTero Software (pre-loaded)
90 Day Parts Warranty
User Manual(s)
Free Standard Shipping (Commercial USA Addresses)
Its ergonomic design comes with safe docking station. It has thin fiber optic cable which enables quick data transfer from the wand to the cart. This optimized cable length assists various cart positions in the operatory.Orthodontic treatment is more than just straightening teeth; it’s about ensuring your teeth and jaws are in alignment. To achieve this, we need to get an accurate look at where your teeth are positioned. To do this, we use the iTero Intraoral digital scanner.A good impressionIn the orthodontic and dental industries, ‘impressions’ is the term we use for getting a good picture of where your teeth currently sit. These impressions were previously taken using a type of dental cement. Pasted on your teeth, patients were required to lie for a few minutes while the cement-like material set. The dental professional could then remove the set material which had formed an ‘impression’ of your teeth.This process was messy, rather unpleasant and not very comfortable. Fortunately, that method is a thing of the past. These days, we use scanning technology and at L&L Orthodontics, our technology of choice is the iTero Intraoral digital scanner.
What is the iTero scanner?
The iTero scanner is new 3D orthodontic scanning technology. Using the latest developments in intraoral scanning, the iTero scanner accurately scans your teeth as part of your orthodontic assessment. The iTero scanner is made up of a small, wand-like device which is used to scan your teeth and jaws. The data it is collecting then appears on the computer screen, allowing you to see the ‘impressions’ the scanner is taking.The iTero scanner works in with Invisalign®* treatment and lets you see what your teeth will look like post-treatment, even before you’ve started. Before we recommend a course of treatment for you, we’ll take impressions of your teeth using the iTero scanner to ensure we are making our recommendation on accurate information.To find out more about the iTero scanner and other orthodontic technology we use here at L&L Orthodontics, book your specialist consultation today.
Medit Identica T300 Dental 3D Scanner
Identica T300 to meet all of your needs. With powerful scan engine and affordable pricing, the new Identica T300 is a perfect fit for both performance enthusiasts and entry level users. Its evolutionary design and high tech features will help your lab rediscover productivity. Bundled colLab 2017 scan software makes scan data processing easy and efficient.Quality & affordability
2.0 MP cameras, Blue LED
Accuracy : 7 μm (ISO)
Full arch scan time 24 sec
2-Axis Manual
Identica T300 dramatically improves the most important aspects of scanner performance. The latest software technology provides you with the cleanest and sharpest data. T300 is specially designed to bring out the finest data quality using its 2.0 MP cameras. T300 will save your precious time and money by minimizing trial & error to adjust restoration fits.Identica T300 is an upgrade version of Identica Blue, provided at lowest pricing. Giving better value for the affordable scanner users. Identica T300 has enhanced data quality compared to Identica Blue.
Introducing the Next Generation of 3D Dental Scanners: Our T-Series
Medit represents the apex in 3D dental scanning. With unsurpassed speed, accuracy, and reliability, Medit helps you rediscover your productivity. The T-Series’ new powerful scan engine and affordable pricing are the perfect fit for performance enthusiasts and entry-level users, helping your lab rediscovering productivity thanks to its convenient design and high-tech features.
Medit T300 is the latest Medit scanner with an enhanced SW scan. It uses Blue Light technology, which enables quick scanning and provides excellent precision (7μm).The program is user-friendly, because it takes you through simple and fast individual steps, from inserting the model into the scanner to exporting the file to the CAD design program.FEATURES:Medit Identica T300 Dental 3D Scanner
Scanned printing: 2 manual axes.
Touch sensor: no.
Full arcade scan speed: 24 ´´
Resolution of the camera: 2 x 2 MP camera.
Scan volume: 90 x 72 x 60 mm.
Scanning principle: Optical change phase.
Dimensions: 290 x 290 x 340 mm.
Weight: 12Kg.
Light source: Blue LED.
Connectivity: Type USB 3.0 B.
Power: 100- 240 vac, 50-60 HZ.
Warranty: 2 years.
ADVANCED DATA PROCESSING AND HIGHER RESOLUTION DUAL CAMERAS
The Identica T300 dramatically improves the fundamental aspects of scanner performance and the latest software technology provides the clearest, sharpest data. Identica T300 is customized to deliver the finest data quality using its dual 2.0 MP cameras. Identica T300 will save valuable time and money by minimizing trial & error when adjusting restoration fits.
XIOS scan Sirona
XIOS Scan. Small change. Big impact.
The XIOS scan provides a gentle, easy introduction into the world of digital X-ray imaging. If you want to switch from film to digital without having to give up your tried-and-true working methods, imaging plate technology offers you a myriad of possibilities. You can experience many of the advantages of digital imaging without a darkroom and chemicals while your team continues its regular workflow. XIOS Scan completes the family of intraoral X-ray systems from Sirona which includes the sensors XIOS XG and the intraoral X-ray HELIODENTPLUS source.
Tried-and-true workflow meet the advantages of digital imaging
Outstanding scan quality with 22 line pairs/mm
Scratch-free scanning and automatic film detection
Proven Sirona quality “Made in Germany”Technical data
XIOS Scan
Dimensions (H x W x D) 363 mm x 163 mm x 286 mm
Weight 7.3 kg ± 0.5 kg
Pixel size selectable 23/30 μm
Resolution 22/17 Lp/mm
Interface LAN
Dimensions
Storage plate intraoral
Size 0 31 mm x 22 mm
Size 1 24 mm x 40 mm
Size 2 31 mm x 41 mm
Size 3 27 mm x 54 mmSmall Change. Big Impact.
Xios Scan provides a gentle, easy introduction into the world of digital X-ray imaging. If you want to switch from film to digital without having to give up your tried-and-true working methods, imaging plate technology offers you a myriad of possibilities. You can experience many of the advantages of digital imaging without a darkroom and chemicals while your team continues its regular workflow.The Xios Scan integrates seamlessly with the Dentsply Sirona X-ray units and software to deliver better, safer and faster intraoral diagnostics.For the best digital image quality and the easiest workflowXios Scan works at an outstanding resolution of up to 22 line pairs/mm (theoretical resolution). The result is exceptionally sharp and detailed images - ideal conditions for an accurate diagnosis. The images are transmitted directly to Sidexis 4, Dentsply Sirona Imaging's software, where they can then be further evaluated and diagnosed. The software provides simple controls for later editing of the visual impression of the X-ray in terms of sharpness, brightness and contrast.
The DWX-52DC Dental Mill with Disc Changer is the newest addition to the popular DWX series of 5-Axis Dental Milling Machines. With a combination of automated functions designed to help reduce manual work, production of dental restorations is now even more efficient and reliable. The DWX-52DC’s open architecture means it can be used with the CAD/CAM software that your technicians are already familiar with in order to cut learning time and create the optimum workflow for your production environment. The DWX-52DC provides an efficient digital solution for both dental laboratories seeking to boost production capabilities, as well as labs looking to expand into the digital realm.
95 mm (diameter), height max. 35 mm
Pin diameter: 6 mm
Pin diameter:
6 mm
Loadable workpiece weight
Up to 850 g
Number of adapters housed
6
Operating speed
XYZ axis:
0.24 to 70.9 in./min.(6 to 1,800 mm/min.)
Spindle motor
Brushless DC Motor
Spindle speed
6,000 to 30,000 rpm
Rotary axis travel angle
A:
±360°
B:
±30°
Number of burs housed
15
Attachable bur
Shank diameter:
4 mm
Length:
40 to 55 mm
Compatible compressed air
0.2 MPa
Interface
USB
Control command set
RML-1, NC code
Power requirements
AC 100 V to 240 V ±10%, 50/60 Hz, 2.0 A
(overvoltage category II, IEC60664-1)
Power consumption
Approx. 200 W
Operating noise
During operation:
70 dB (A) or less (when not cutting),
During standby:
45 dB (A) or less
External dimensions
Width x Depth x Height:
34.6 x 26.0 x 23.6 in. (880 x 660 x 600 mm)
Weight:
105 kg (231.5 lbs.)
The ultimate in ease, material flexibility and unattended production, the DWX-52DC dental milling machine is designed to greatly expand your lab production and profit. Featuring a 6-slot Automatic Disc Changer, 15-station Automatic Tool Changer and other automated features, it gives users of all skill levels an exceptionally powerful, efficient and affordable dental restoration solution.
The DWX-42W enables wet milling of popular glass-ceramic composite resins with high precision and accuracy. High-Speed Production with proprietary DGSHAPE spindle. Expanded 6-tool Automatic Tool Changer for uninterrupted milling. LAN capable for network and hardware connection and communication. VPanel user interface for easy monitoring of milling jobs and tools.The DGSHAPE DWX-42W enables wet milling of popular glass ceramic and composite resins with high precision and accuracy.
High speed production with proprietary DGSHAPE spindle
Expanded 6-tool Automatic Tool Changer for uninterrupted milling
LAN capable for easy connectivity
Included VPanel for easy monitoring of milling jobs and tools
Reviews
There are no reviews yet.